REVOLABS FLX2TM Wireless Conference System for analog phone lines System Guide Models: 10-FLX2-200-POTS 10-FLX2-020-POTS 10-FLX2-002-POTS
10 Installing FLX2 Components The Revolabs FLX2TM System is comprised of several components that work together to provide you with a great wireless c
11 FLX2 Charger Base The FLX2 Charger Base, shown below, provides charging capabilities for all battery operated system components, including the Dia
12 FLX Dialer The FLX Dialer equips the user with an intuitive and interactive tool for configuring and operating the FLX System. The Dialer is not
13 FLX Speaker The FLX Speaker, shown below, is a wireless active omnidirectional speaker that has been designed and optimized specifically for use w
14 FLX Microphones The FLX Microphones provide a sleek and unobtrusive form factor allowing for closer proximity to the participants and creating the
15 Initial Setup After unpacking the FLX2 Conferencing System, there are a few initial setup tasks that must be performed before a call can take plac
16 Handset Mode Handset mode allows a telephone call to take place through the handset speaker and microphone located in the FLX Dialer. This allows
17 used. All other speakers must be switched off. Any Echo Cancellation provided on the Video Conferencing unit must be switched off. N
18 Answering an Incoming Telephone Call 1. When the FLX2 System identifies an incoming call, it will play the ring tone through the FLX Speaker. If
19 Ending a Telephone call 1. A call can be ended in two fashions. a. Press the Red ‘End Call’ button on the FLX Dialer during a call. b. Place t
2 © 2011 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without exp
20 Muting a Call 1. In handset mode, the ‘Mute’ and ‘UnMute’ key will mute/unmute the FLX Dialer microphone, not the wireless Microphones. 2. In sp
21 Conference Call 1. Press the ‘Enter’ key to access the Active Call Menu and select ‘Conference’. 2. Create the second call by selecting Dialer,
22 When the Dialer is removed from the Charger Base no change to call activity will take place. If there is no active call, the Dialer will revert to
23 Bluetooth The FLX2 System is equipped with a Bluetooth interface allowing a call to be placed through a cell phone, computer, or 3rd party Bluetoo
24 Adding a Device 1. Go to the Menu Bluetooth. Select ‘Discovery Mode’ to activate Bluetooth and accept Bluetooth Request from other devices. 2.
25 Accepting Device Connection Request If the trust setting for a previously paired Bluetooth device is set to ‘Ask’ and that device comes into range
26 Video Conference Collaboration The FLX2 System is equipped with balanced analog audio input and output to be connected to 3rd party video or PC co
27 Mixing the audio signals As discussed earlier, Audio and Video, or Bluetooth and Video calls can be made simultaneously from a FLX system, requiri
28 FLX2 System Configuration There are many features to the FLX2 System that can be modified and configured using the FLX Dialer. The following is a
29 Recent Calls The Recent Calls call log stores the contact information from calls placed or received, allowing the user to review recent calls, red
3 Introduction Congratulations on your purchase of the Revolabs FLX2TM Wireless Conference Phone. This system utilizes state of the art technology p
30 View Recent Call Information 1. Access the recent call log by browsing: Menu Recent Calls or pressing the green ‘Call’ button while no call is
31 Delete Call History 1. Access the recent call log by browsing: Menu Recent Calls or pressing the green ‘Call’ button while no call is in progre
32 Edit a Contact 1. Browse to the Contacts menu: Menu Contacts, scroll to the desired contact, and selects ‘View’ to access the contact. 2. The
33 Search for Contact 1. Browse to the Contacts menu: Menu Contacts. 2. Use the keys (0-9) to apply a filter a. Once a key is pressed the title
34 Set Speed Dial 1. Browse to the Contacts menu: Menu Contacts, scroll to the desired contact, and selects the ‘View’ key to access the contact.
35 Ringer 1. Browse to the Ringer menu: Menu Audio Controls Ringer. 2. Choose ‘Ringer Volume’ in the Ringer Settings menu to adjust the Ringer
36 Device Status 1. Browse to Device Status: Menu Device Status. 2. The Device Status screen shows status for the Microphones and the Speaker.
37 Call When selecting ‘Call’ in the menu, the Dialer will open the Dialer menu, allowing dialing a number. Setup Setup is divided into a generic are
38 Advanced Setup The following is a list of advanced configuration settings that are protected by a 4 digit password for administrator access only.
39 Aux Audio ‘Aux Audio’ is to control the AUX In and AUX Out connections on the base. 1. Aux In ON/OFF and Aux Out ON/OFF allow enabling / disablin
4 Contents Introduction ...
40 Setting System Name 1. Go to Menu Setup Advanced Setup Admin Settings Set System Name. 2. Change the current System Name to the new name,
41 Pairing All FLX2 wireless components are paired before the system is shipped, providing much of the system setup already completed. While pairing
42 7. After a short time an overlay will appear on the FLX Dialer saying ‘Pairing Successful’, after which the screen should read ‘SPK 1 Linked’. 8.
43 Phone Settings 1. Browse to the Phone Settings menu: Menu Setup Advanced Setup Phone Settings. a. You can change the dialing method by sel
44 1. Hold down the button on the bottom of the Speaker until the LED indicators on the top of the Speaker turn green. Once the LED indicators turn
45 2. The Microphone or Speaker lost connection with the Base Station for more than 5 minutes and therefore shut down. It should be returned into r
46 Microphone, Speaker, or Dialer not paired with Base Station Please follow the descriptions on page 41 on how to pair the different components with
47 LED Indicators Device LED Indicator Status Microphone in Charger Base Steady Red Charging Steady Green Fully charged Single red flash Active phone
48 Device LED Indicator Status Steady Red o Connected, battery charging, phone call in progress, Master Mute or “All Mic Mute” is ON, all Microphone
49 Device LED Indicator Status Flashing Yellow* – Red – Yellow* – Green Searching for a connection to the base The speaker will try to re-establish
5 System Information ...
50 Technical Specifications Models The Revolabs FLX2 System is available with a variety of configurations to provide the best audio capture in the in
51 Microphones Dimensions Microphones 94.2 x 24.6mm x 18.5mm (omnidirectional Microphone) Weight 28.6g (omnidirectional Microphone) Bandwidth 80-1
52 Regulatory Information FCC Notice to Users Users are not permitted to make changes or modify the equipment in any way. Changes or modifications no
53 Restricted use with certain medical devices Hearing Aids Some devices may interfere with some hearing aids. In the event of such interference, you
54 E C Declaration of Conformity Manufacturer’s Name: Revolabs Manufacturer’s Address: 144 North Road, Suite 3250 Sudbury, MA 01776 U.S.A. Mo
55 ACTA Part 68 information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the base of this e
56 Limited Warranty and Limitation of Liability Limited Warranty Revolabs warrants to the end user (“Customer”) that this product will be free
57 Limitation of Liability TO THE FULL EXTENT ALLOWED BY LAW, REVOLABS EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRAC
6 General Information The Revolabs FLX2 Conference Phone includes several components which, in the sum, make up the conferencing phone. The componen
7 Quick setup for Telephone Conference Calls While all components delivered with the Revolabs FLX2 Conference Phone are partially charged, we recomm
8 Making a call To make a conference call, take at least one of the Microphones out of the Charger Base, and take the Dialer out of the Charger Base.
9 Description The Revolabs FLX2™ Wireless Conference Phone is a unique marriage of innovative technology and ergonomic design, allowing for an unpara
Kommentare zu diesen Handbüchern